StakdTrax ENFR Download

Joining a session

Scan a QR code, pick an open session, or type a code.

There are three ways in. On the home screen, tap Join a session: all three are there, and each one joins straight away.

Join a session
Join a session

Scan the QR code

With the Camera app: point your iPhone's camera at the QR code on the host's screen, then tap the banner to open it in StakdTrax.

Inside StakdTrax: tap Join a session, then Scan the host's QR code, and point the camera at the host's screen. StakdTrax asks to use the camera the first time.

A scanned code only joins from the home screen. If your phone is already in a session, StakdTrax tells you rather than leaving it.

Pick an open session

As soon as Join a session opens, open sessions nearby appear by name under Open sessions nearby — tap one to join. A session marked Full can't take another phone. If the search stops, tap Look again.

Closed sessions never appear here. You need their code.

Type the code

Type the six-character code into Join code and tap Join. The dash is added for you. Codes never use the letters I, L, O or U, so typing O gives 0, and I or L gives 1.

Skip the choosing

Settings › Quick start › Join makes Join a session go straight to one way in: the camera, the open session nearby, or the code this phone last joined with. The ⋯ button in the tile's corner still opens all three.

Joining the open session nearby works only when there is exactly one to join — with two in range, or none within a few seconds, it asks.

When the session is on the host's hotspot

If the host is sharing the session over their Personal Hotspot, the QR code names that network. After scanning, StakdTrax shows you which network it is.

  1. Tap Join this network. iOS asks whether to join it — tap Join.
  2. If the host didn't put the password in the code, iOS asks for it too; the host can read it out.
  3. StakdTrax goes on to join the session by itself.

You can also Join the session without it, which only works if your phone can already see the host.

Your phone stays on that network afterwards. Forget it in Settings › Wi-Fi when the practice is over.

Once you're in

Your phone shows the lobby and follows the session from there. You don't need to press anything until the host asks everyone to huddle for calibration.

While it connects, the lobby says how it's going: Looking for the session, Connecting, or Couldn't connect — trying again. It keeps trying for as long as the host's session is in range.

Under that, it says which way it's connecting:

  • Over your shared Wi-Fi — your phone and the host are on the same network. It usually connects in a second or two.
  • Phone to phone — there's no network you both share, and it says why: your phone isn't on a Wi-Fi network, the host isn't, or you're on different ones. The phones connect directly, and it usually takes a second or two.

If a try fails, it suggests what would help for that case. The quickest fix is usually to put your phone on the same Wi-Fi network as the host — see Connecting quickly.

If your phone loses touch with the host later, it reconnects on its own while you stay nearby. If it doesn't come back, tap End and join again.

If the session is full

Session full
Session full

A session holds up to eight phones, and the host can set a lower limit or mark it full. If you try to join one with no room for your phone, it goes back to the home screen and says Session full; the same line stays under Attention until you dismiss it. Ask the host to make room — remove a phone, raise Up to … phones, or turn off Full — no more phones — then join again. See Hosting a session.

Leaving a session

Tap End to leave. The session carries on without your phone, and everything it recorded is kept. Left by mistake? For a minute afterwards, your home screen shows You left with Rejoin the session, which takes your phone back to its old place. After that, join again with the code.

If the host hands the session over

The host can make another phone the host — yours, perhaps — if theirs is running low or they have to leave. Every phone says who the host is now, and the session carries on: the same code, the same takes, no need to huddle again. If your phone is the new host, it gets the host's controls. See Hand the session to another phone.

Getting the stack

When the host finishes, your phone stays in the session, showing Waiting for the stack, until the host has built the stack and sent it. Then it goes home by itself, once every phone has its copy, and the stack is in Your recordings beside your own track. Tap Leave now if you can't wait: the stack comes at the next session with that host instead.

Stacks you missed, and ones the host built again later, arrive the same way the next time you join them. Stacks from the host, in the lobby, shows them coming. A stack that doesn't arrive is sent again the time after.

If the host ends the session

Your phone is told, and goes back to the home screen. Everything it recorded is kept.

If the host ended it by mistake, they can resume it for fifteen minutes. Your home screen shows Session ended with Rejoin when the host resumes it: tap it, and your phone goes back to the session and waits for the host, the same way it does after losing touch. Once the host resumes, it takes up its old place.

If you leave it on the home screen instead, StakdTrax keeps listening for the host. When the session is running again, the card changes to Session resumed and the phone buzzes — tap Rejoin now.

Connecting quickly

A phone usually joins in a second or two, at the first try — on the same Wi-Fi network as the host, or phone to phone with no network at all. The internet isn't used either way.

If a phone keeps failing to connect phone to phone, a shared network helps — the hall's Wi-Fi, a home network, or the host's Personal Hotspot. If your phone shows Couldn't connect — trying again, the lobby suggests it. Join it in Settings › Wi-Fi, then come back to StakdTrax, which carries on trying.

No Wi-Fi network?

StakdTrax doesn't need a Wi-Fi network or the internet — the phones can connect to each other directly, which is how it works outdoors. But Wi-Fi and Bluetooth both have to be switched on, even with no network nearby. If a phone can't connect directly, the host's Personal Hotspot is the way in — see Connecting quickly.

  • Turning Wi-Fi off in Control Center is fine: it only disconnects from networks.
  • Turning Wi-Fi or Bluetooth off in Settings, or turning on Airplane Mode without switching them back on, stops the phones finding each other.